Free Shipping with $99+ Purchase Details

Free Shipping with $99+ Purchase

Restrictions

Free shipping applicable to only UPS Ground - lower 48 United States - on purchases of $99 or more in the same order. Taxes and prior purchases do not qualify toward the minimum purchase requirement and offer cannot be applied to such items. Eligible customers must select this option during checkout in order to receive free shipping. Not applicable to dealers.

  •  
  • HOME > PRODUCTS > Z-Wave Multi-input/output Dry Contact Bridge

    Z-Wave Multi-input/output Dry Contact Bridge

    MIMOliteUS
    $59.99

    Manufacturer: Fortrezz

    Model: Z-Wave Multi-input/output Dry Contact Bridge


    Make virtually any device speak Z-wave with the MIMOlite Module! The MIMOliteUS is an interface / bridge module, capable of converting a digital or analog voltage input and/or a Z-Wave RF message input to a dry contact relay output and/or a Z-Wave RF message output.

    • Description
    • Specs
    • Docs
    • Reviews

    The MIMOlite module provides one input and one relay output (isolated dry contacts, NO-COM-NC) and is capable of Z-Wave input/output/control. The system includes a program switch for Z-Wave inclusion/exclusion and an LED for various status indications.

    • Connect one wired devices to Signal input and make them wireless.
    • Connect them functionally to your Home Security panel OR to your z-wave home automation network
    • Connect high or low up to 24V digital signals
    • Connect pulse reading devices
    • Connect up to 24V analog signals

    Input SIG1 is an analog input, internally pulled-up to the MIMOlite supply voltage. The system allows trigger conditions to be set based on the input voltage being inside or outside a user-defined range (configured via Z-Wave). This provides great flexibility for capturing events in a wide variety of applications.

    The trigger status of the input can be read via Z-Wave and/or can be automatically sent to a configured node, typically the Controller. In addition, a count of the trigger events that have occurred for each input channel are internally recorded (and stored in the 'pulse count') and are available to be read via Z-Wave. The current triggered/un-triggered status can also be read via Z-Wave.

    The SIG1 input can be associated with up to two other Z-Wave devices, such that an associated device will automatically turn on (or off) based on the occurrence of a trigger event. Finally, the analog input channels can be configured so that they periodically send the analog input level (not just trigger status) to up to two other associated nodes.

    The output relay is, typically, commanded via Z-Wave commands. In addition, the user can configure the input SIG1 trigger condition to be mapped to the output relay. Thus, for example, Relay 1 can be automatically turned on based on Input SIG1 being triggered. The relay activation can be set via a jumper or via Z-Wave for either momentary or latched operation - see Installation section of the User Manual.

    MIMOlite comes in a plastic enclosure for indoor use only.


    Specifications:
    • Power: 9-24 V DC or 9-18V AC from a power supply @~ 300mA capability
    • Frequency Range: 908.4MHz (US); 868.4MHz (EU)
    • Distance Range: Max 100ft line of sight in unobstructed environment
    • Enclosure Size (L x W x D): 3 3/8"" (85mm) x 2 1/2"" (64mm) x 1 1/4"" (30mm)
    • Weight: 4 oz (100 gram)
    • Operating Temperature: -10⁰C (14F) to +70⁰C (158F)
    • Input Signal 1 (SIG1): Digital or Analog Input 0 to 24V DC or 16 Hz Max for pulse counting (minimum 32 ms high or low time). The trigger levels and hysteresis can be set via the Configuration
    • Command Class for the two endpoints.
    • Input Signal Impedance Input impedance for SIG1 is Z=66 ohm at 10KHz. This impedance is = 66 ohm = 34 ohm + j 540uH.
    • Output Relay 1: DPDT, Max. Switching power of 120W; 10uA to 10A; High Dielectric strength coil-contacts: 1,000 VAC;
    • Open contacts: 750 VAC; Conforms to FCC Part 68 requirements; Ag + Au clad bifurcated contacts fully sealed.
    • System Requirement: Any Z-WaveTM -enabled network and controller.
    • FCC and Canada IC certified for 908.4 MHZ Z-Wave RF communications.
    • Complies with European Test standard: ETSI EN 300 220 for 868.4 MHZ Z-Wave RF communications.

    Be the first to make a review.

    You must be logged in to add a review

    Click the at the top of the page to log in.


 
0