Appliance Plug-in Module – RFAPM
CAUTION:
• Use only with 120V/AC 60 Hz.
• Do not exceed the maximum rating as indicated on the
device: Incandescent, 600Watts.
• Do not use to control appliances like an electric oven,
iron or any device that requires supervision when on.
• If you are unsure of any part of these instructions,
contact a licensed electrician.
FEATURES:
1. Easy to install, uses existing receptacles.
2. Control a load by using the switch on the side of the
module.
3.Wirelessly control a device that is plugged into the module using Z-Wave®.
4. Can include device plugged into the module into customized scenes.
USER INSTRUCTIONS:
1. Plug the appliance module into a wall receptacle; preferably one that is not controlled by a switch.
2. Connect the lamp plug into the module. NOTE: Some plugs are polarized and may have to be
rotated before connecting.
3. Install the appliance module in the Z-Wave network using the instructions below.
4. The appliance module is now ready to be used as a wirelessly controlled device.
Z-Wave™ Device Network Installation Instructions:
1. This product may be added to a new or existing Z-Wave network. The device has an amber LED,
which will blink when the device is not included in a Z-Wave network. The LED stops blinking
when the device is included in a network.
2. To include this device in a Z-Wave network, select the command on your ZWave controller for
inclusion (Install, Add Device, Add Node, Include Device, etc.). Then press the device control switch one time to include it in
the network. The LED will stop blinking.
3. To exclude this device from a Z-Wave network, select the command on your Z-Wave controller for exclusion (Uninstall,
Remove Device, Remove Node, Exclude Device, etc.). Then press the device control switch one time to exclude it from the
network. The LED will start blinking.
4. This product works with other Z-Wave products from different vendors and product categories as part of the same network.
5. This product is a listening node and it will act as a repeater in the Z-Wave network. It will perform the repeater function with
Z-Wave products from Cooper and from other Z-Wave vendors.
Troubleshooting Guide
Symptom Possible Cause Solution
No Function. Device status a) Lamp is burnt out a) Replace light bulb
LED is OFF b) Lamp switch is turned OFF b) Turn the lamp switch on.
c) Circuit breaker is off or tripped c) Turn on the circuit breaker
d)Wall switch to control wall d) Turn on switch and keep it ON at all times.
receptacle is turned OFF NOTE: Recommend to plug into a receptacle not
controlled by a switch.
e)Wall receptacle is not live e) Check circuit breaker, if needed contact
licensed electrician
Erratic operation or flickering a) Appliance module plug not fully a) Insert appliance module plug fully into the
status LED inserted into the wall receptacle wall receptacle
b) Lamp plug not inserted into the b) Insert lamp plug fully into the appliance module
Z-Wave appliance module receptacle receptacle
fully
Functions normally using the Appliance module not included in the Include module in the Z-Wave network
control switch but not from the network using a Z-Wave controller. Refer to Z-Wave
Z-Wave controller and the status controller user manual for details
LED on the module blinks ON and
OFF about once per second.
Functions normally using the Problem with RF communication on the Replace the appliance module
appliance module control appliance module
switch but not from the Z-Wave
controller and the Status LED
is not blinking
Functions normally both The appliance module is not associated Create association between the appliance
locally and from the Z-Wave with other Z-Wave devices module and other Z-Wave devices. Refer to
controller but cannot be Z-Wave controller user manual for details
controlled using other
Z-Wave devices
STATUS LED
TÉMOIN D’ÉTAT
LED DE ESTADO
CONTROL SWITCH
INTERRUPTEUR DE COMMANDE
INTERRUPTOR DE CONTROL
INCLUSION/INCLUSIÓN
ON/OFF CONTROL
COMMANDE MACHE/ARRÊT
CONTROL DE ENCENDIDO/APAGADO
RFPLUG-PTA
|
